IP Camera Aviosys-9060AK: Unable to open video device.
Question
Hi,
I get "Unable to open video device."
I am using few IP cameras Aviosys-9060AK
http://www.aviosys.com/ip9060akplus.htm
i tried:
- trunk version 511
- port forcing for netcam_url
- netcam_url like "mjpg://"
- netcam_url for snapshot.jpg
motion.x86_64 3.2.11.1-3.fc12
ffmpeg.x86_64 0.5-5.20091026svn.fc12
mysql.x86_64 5.1.45-2.fc12
Snapshot.jpg in browser is OK.
Videostream in other software is OK (showing).
What should else i try?
Thank You for help in advance.
BRGDS Pavel
PS My small grant - 50$ for solution with both
netcam_url http://192.168.0.106:80/snapshot.jpg
and
netcam_url http://192.168.0.106:80/cgi-bin/Stream?Video
[root@phenom log]# motion -n -d 9
[0] [ALR] [ALL] conf_load: Processing thread 0 - config file /usr/local/etc/motion.conf
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_output_movies"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_output_debug_movies"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_timelapse"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_timelapse_mode"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_bps"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_variable_bitrate"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_video_codec"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "ffmpeg_deinterlace"
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "movie_filename"
Message from syslogd@localhost at Apr 28 00:41:41 ...
motion: [0] [EMG] [ALL] motion_startup: Motion trunkREV511 Started
Message from syslogd@localhost at Apr 28 00:41:41 ...
motion: [0] [EMG] [ALL] motion_startup: Logging to syslog
[0] [ALR] [ALL] conf_cmdparse: Unknown config option "timelapse_filename"
[0] [EMG] [ALL] motion_startup: Motion trunkREV511 Started
[0] [EMG] [ALL] motion_startup: Logging to syslog
[0] [EMG] [ALL] motion_startup: Using log type (ALL) log level (ALL)
Message from syslogd@localhost at Apr 28 00:41:41 ...
motion: [0] [EMG] [ALL] motion_startup: Using log type (ALL) log level (ALL)
[0] [ERR] [ALL] main: Thread 1 is from /usr/local/etc/motion.conf
[0] [DBG] [ALL] main: Thread 1 is device: http://192.168.0.106:80/cgi-bin/Stream?Video input -1
[0] [DBG] [ALL] main: Stream port 8081
[0] [DBG] [ALL] main: Waiting for threads to finish, pid: 3827
[1] [DBG] [ALL] motion_init: Thread 1 started
[1] [ALR] [NET] netcam_start: Network Camera thread starting... for url (http://192.168.0.106:80/cgi-bin/Stream?Video)
[1] [DBG] [NET] netcam_url_parse: Entry netcam_url_parse data http://192.168.0.106:80/cgi-bin/Stream?Video
[1] [DBG] [NET] netcam_url_parse: Parse case 0 data http://192.168.0.106:80/cgi-bin/Stream?Video
[0] [ALR] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 8080
[1] [DBG] [NET] netcam_url_parse: Parse case 1 data http
[1] [DBG] [NET] netcam_url_parse: Parse case 6 data 192.168.0.106
[1] [DBG] [NET] netcam_url_parse: Parse case 7 data :80
[1] [DBG] [NET] netcam_url_parse: Parse case 8 data 80
[0] [ALR] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 8080
[1] [DBG] [NET] netcam_url_parse: Parse case 9 data /cgi-bin/Stream?Video
[0] [ALR] [STR] httpd_run: motion-httpd/trunkREV511 running, accepting connections
[0] [ALR] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 8080
[1] [INF] [NET] netcam_start: Netcam_http parameter 'off' converts to flags: HTTP/1.0: 1 HTTP/1.1: 0 Keep-Alive OFF.
[1] [INF] [NET] netcam_start: now calling netcam_setup_html()
[1] [INF] [NET] netcam_http_build_url: Netcam has flags: HTTP/1.0: 1 HTTP/1.1: 0 Keep-Alive OFF.
[1] [INF] [NET] netcam_http_build_url: Camera connect string is ''GET /cgi-bin/Stream?Video HTTP/1.0
Host: 192.168.0.106
User-Agent: Motion-netcam/trunkREV511
Connection: close
'' End of camera connect string.
[1] [INF] [NET] netcam_http_request: about to try to connect, time #0
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 5
[1] [INF] [NET] netcam_connect: re-using socket 5 since keepalive is set.
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [INF] [NET] netcam_http_request: about to try to connect, time #1
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 5
[1] [INF] [NET] netcam_connect: re-using socket 5 since keepalive is set.
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [INF] [NET] netcam_http_request: about to try to connect, time #2
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 5
[1] [INF] [NET] netcam_connect: re-using socket 5 since keepalive is set.
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [INF] [NET] netcam_http_request: about to try to connect, time #3
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 5
[1] [INF] [NET] netcam_connect: re-using socket 5 since keepalive is set.
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [INF] [NET] netcam_http_request: about to try to connect, time #4
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 5
[1] [INF] [NET] netcam_connect: re-using socket 5 since keepalive is set.
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [ERR] [NET] netcam_http_request: Failed to read first camera header - giving up for now
[1] [ERR] [ALL] motion_init: Could not fetch initial image from camera Motion continues using width and height from config file(s)
[1] [ERR] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
[1] [EMG] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
[1] [EMG] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
[1] [DBG] [ALL] motion_init: Started motion-stream server in port 8081
[1] [DBG] [ALL] motion_loop: vid_return_code 1
Message from syslogd@localhost at Apr 28 00:41:46 ...
motion: [1] [EMG] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Message from syslogd@localhost at Apr 28 00:41:46 ...
motion: [1] [EMG] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [DBG] [ALL] motion_loop: vid_return_code 1
[1] [DBG] [ALL] motion_loop: vid_return_code 1
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [DBG] [ALL] motion_loop: vid_return_code 1
[1] [DBG] [ALL] motion_loop: vid_return_code 1
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [DBG] [ALL] motion_loop: vid_return_code 1
[1] [DBG] [ALL] motion_loop: vid_return_code 1
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [DBG] [ALL] motion_loop: vid_return_code 1
[1] [ERR] [ALL] motion_loop: Retrying until successful connection with camera
[1] [ALR] [NET] netcam_start: Network Camera thread starting... for url (http://192.168.0.106:80/cgi-bin/Stream?Video)
[1] [DBG] [NET] netcam_url_parse: Entry netcam_url_parse data http://192.168.0.106:80/cgi-bin/Stream?Video
[1] [DBG] [NET] netcam_url_parse: Parse case 0 data http://192.168.0.106:80/cgi-bin/Stream?Video
[1] [DBG] [NET] netcam_url_parse: Parse case 1 data http
[1] [DBG] [NET] netcam_url_parse: Parse case 6 data 192.168.0.106
[1] [DBG] [NET] netcam_url_parse: Parse case 7 data :80
[1] [DBG] [NET] netcam_url_parse: Parse case 8 data 80
[1] [DBG] [NET] netcam_url_parse: Parse case 9 data /cgi-bin/Stream?Video
[1] [INF] [NET] netcam_start: Netcam_http parameter 'off' converts to flags: HTTP/1.0: 1 HTTP/1.1: 0 Keep-Alive OFF.
[1] [INF] [NET] netcam_start: now calling netcam_setup_html()
[1] [INF] [NET] netcam_http_build_url: Netcam has flags: HTTP/1.0: 1 HTTP/1.1: 0 Keep-Alive OFF.
[1] [INF] [NET] netcam_http_build_url: Camera connect string is ''GET /cgi-bin/Stream?Video HTTP/1.0
Host: 192.168.0.106
User-Agent: Motion-netcam/trunkREV511
Connection: close
'' End of camera connect string.
[1] [INF] [NET] netcam_http_request: about to try to connect, time #0
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 6
[1] [INF] [NET] netcam_connect: re-using socket 6 since keepalive is set.
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [INF] [NET] netcam_http_request: about to try to connect, time #1
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 6
[1] [INF] [NET] netcam_connect: re-using socket 6 since keepalive is set.
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [INF] [NET] netcam_http_request: about to try to connect, time #2
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 6
[1] [INF] [NET] netcam_connect: re-using socket 6 since keepalive is set.
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [INF] [NET] netcam_http_request: about to try to connect, time #3
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 6
[1] [INF] [NET] netcam_connect: re-using socket 6 since keepalive is set.
[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 0
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [INF] [NET] netcam_http_request: about to try to connect, time #4
[1] [INF] [NET] netcam_connect: disconnecting netcam since keep-alive not set.
[1] [INF] [NET] netcam_connect: with no keepalive, new socket created fd 6
[1] [INF] [NET] netcam_connect: re-using socket 6 since keepalive is set.
^C[0] [DBG] [ALL] main: DEBUG-2 threads_running 1 motion_threads_running 1 finish 1
Message from syslogd@localhost at Apr 28 00:41:55 ...
motion: [0] [EMG] [STR] httpd_run: motion-httpd - Finishing
Message from syslogd@localhost at Apr 28 00:41:55 ...
motion: [0] [EMG] [STR] httpd_run: motion-httpd Closing
[0] [EMG] [STR] httpd_run: motion-httpd - Finishing
[0] [EMG] [STR] httpd_run: motion-httpd Closing
[0] [EMG] [STR] motion_web_control: motion-httpd thread exit
Message from syslogd@localhost at Apr 28 00:41:55 ...
motion: [0] [EMG] [STR] motion_web_control: motion-httpd thread exit
Message from syslogd@localhost at Apr 28 00:41:55 ...
motion: [1] [EMG] [ALL] motion_loop: Thread exiting
[1] [INF] [NET] netcam_read_first_header: Received first header ('**�#')
[1] [INF] [NET] netcam_read_first_header: HTTP Result code -1
[1] [ERR] [NET] netcam_http_request: Error reading first header - re-trying
[1] [ERR] [NET] netcam_http_request: Failed to read first camera header - giving up for now
[1] [DBG] [ALL] motion_loop: vid_return_code 1
[1] [DBG] [ALL] motion_loop: End of event 1
[1] [EMG] [ALL] motion_loop: Thread exiting
[1] [ALR] [STR] stream_stop: Closing motion-stream listen socket & active motion-stream sockets
[1] [ALR] [STR] stream_stop: Closed motion-stream listen socket & active motion-stream sockets
[0] [DBG] [ALL] main: DEBUG-1 threads_running 0 motion_threads_running 0 , finish 1
[0] [DBG] [ALL] main: Threads finished
Message from syslogd@localhost at Apr 28 00:41:57 ...
motion: [0] [EMG] [ALL] main: Motion terminating
[0] [EMG] [ALL] main: Motion terminating
[root@phenom log]# wget -O /dev/null -S http://192.168.0.106:80/cgi-bin/Stream?Video
--2010-04-28 00:44:23-- http://192.168.0.106/cgi-bin/Stream?Video
У�танавливает�� �оединение � 192.168.0.106:80... �оединение у�тановлено.
Запро� HTTP по�лан, ожидает�� ответ...
Длина: нет информации
Saving to: «/dev/null»
[ <=> ] 501 190 57,6K/s
It means "data is going".
motion.conf:
# Rename this distribution example file to motion.conf
#
# This config file was generated by motion trunkREV511
############################################################
# Daemon
############################################################
# Start in daemon (background) mode and release terminal (default: off)
daemon on
# File to store the process ID, also called pid file. (default: not defined)
process_id_file /var/run/motion/motion.pid
############################################################
# Basic Setup Mode
############################################################
# Start in Setup-Mode, daemon disabled. (default: off)
setup_mode off
# Use a file to save logs messages, if not defined stderr and syslog is used. (default: not defined)
;logfile /tmp/motion.log
# Level of log messages [1..9] (EMR, ALR, CRT, ERR, WRN, NTC, ERR, DBG, ALL). (default: 4 / ERR)
log_level 4
# Filter to log messages by type (STR, ENC, NET, DBL, EVT, TRK, VID, ALL). (default: ALL)
log_type all
###########################################################
# Capture device options
############################################################
# Videodevice to be used for capturing (default /dev/video0)
# for FreeBSD default is /dev/bktr0
videodevice /dev/video0
# v4l2_palette allows to choose preferable palette to be use by motion
# to capture from those supported by your videodevice. (default: 17)
# E.g. if your videodevice supports both V4L2_PIX_FMT_SBGGR8 and
# V4L2_PIX_FMT_MJPEG then motion will by default use V4L2_PIX_FMT_MJPEG.
# Setting v4l2_palette to 2 forces motion to use V4L2_PIX_FMT_SBGGR8
# instead.
#
# Values :
# V4L2_PIX_FMT_SN9C10X : 0 'S910'
# V4L2_PIX_FMT_SBGGR16 : 1 'BYR2'
# V4L2_PIX_FMT_SBGGR8 : 2 'BA81'
# V4L2_PIX_FMT_SPCA561 : 3 'S561'
# V4L2_PIX_FMT_SGBRG8 : 4 'GBRG'
# V4L2_PIX_FMT_SGRBG8 : 5 'GRBG'
# V4L2_PIX_FMT_PAC207 : 6 'P207'
# V4L2_PIX_FMT_PJPG : 7 'PJPG'
# V4L2_PIX_FMT_MJPEG : 8 'MJPEG'
# V4L2_PIX_FMT_JPEG : 9 'JPEG'
# V4L2_PIX_FMT_RGB24 : 10 'RGB3'
# V4L2_PIX_FMT_SPCA501 : 11 'S501'
# V4L2_PIX_FMT_SPCA505 : 12 'S505'
# V4L2_PIX_FMT_SPCA508 : 13 'S508'
# V4L2_PIX_FMT_UYVY : 14 'UYVY'
# V4L2_PIX_FMT_YUYV : 15 'YUYV'
# V4L2_PIX_FMT_YUV422P : 16 '422P'
# V4L2_PIX_FMT_YUV420 : 17 'YU12'
#
v4l2_palette 17
# Tuner device to be used for capturing using tuner as source (default /dev/tuner0)
# This is ONLY used for FreeBSD. Leave it commented out for Linux
; tunerdevice /dev/tuner0
# The video input to be used (default: 8)
# Should normally be set to 0 or 1 for video/TV cards, and 8 for USB cameras
input 8
# The video norm to use (only for video capture and TV tuner cards)
# Values: 0 (PAL), 1 (NTSC), 2 (SECAM), 3 (PAL NC no colour). Default: 0 (PAL)
norm 0
# The frequency to set the tuner to (kHz) (only for TV tuner cards) (default: 0)
frequency 0
# Rotate image this number of degrees. The rotation affects all saved images as
# well as movies. Valid values: 0 (default = no rotation), 90, 180 and 270.
rotate 0
# Image width (pixels). Valid range: Camera dependent, default: 352
width 320
# Image height (pixels). Valid range: Camera dependent, default: 288
height 240
# Maximum number of frames to be captured per second.
# Valid range: 2-100. Default: 100 (almost no limit).
framerate 2
# Minimum time in seconds between capturing picture frames from the camera.
# Default: 0 = disabled - the capture rate is given by the camera framerate.
# This option is used when you want to capture images at a rate lower than 2 per second.
minimum_frame_time 0
# URL to use if you are using a network camera, size will be autodetected (incl http:// ftp:// or file:///)
# Must be a URL that returns single jpeg pictures or a raw mjpeg stream. Default: Not defined
; netcam_url http://192.168.0.106:80/snapshot.jpg
netcam_url http://192.168.0.106:80/cgi-bin/Stream?Video
# Username and password for network camera (only if required). Default: not defined
# Syntax is user:password
; netcam_userpass value
# The setting for keep-alive of network socket, should improve performance on compatible net cameras.
# off: The historical implementation using HTTP/1.0, closing the socket after each http request.
# force: Use HTTP/1.0 requests with keep alive header to reuse the same connection.
# on: Use HTTP/1.1 requests that support keep alive as default.
# Default: off
netcam_keepalive off
# URL to use for a netcam proxy server, if required, e.g. "http://myproxy".
# If a port number other than 80 is needed, use "http://myproxy:1234".
# Default: not defined
; netcam_proxy value
# Set less strict jpeg checks for network cameras with a poor/buggy firmware.
# Default: off
netcam_tolerant_check off
# Let motion regulate the brightness of a video device (default: off).
# The auto_brightness feature uses the brightness option as its target value.
# If brightness is zero auto_brightness will adjust to average brightness value 128.
# Only recommended for cameras without auto brightness
auto_brightness off
# Set the initial brightness of a video device.
# If auto_brightness is enabled, this value defines the average brightness level
# which Motion will try and adjust to.
# Valid range 0-255, default 0 = disabled
brightness 0
# Set the contrast of a video device.
# Valid range 0-255, default 0 = disabled
contrast 0
# Set the saturation of a video device.
# Valid range 0-255, default 0 = disabled
saturation 0
# Set the hue of a video device (NTSC feature).
# Valid range 0-255, default 0 = disabled
hue 0
############################################################
# Round Robin (multiple inputs on same video device name)
############################################################
# Number of frames to capture in each roundrobin step (default: 1)
roundrobin_frames 1
# Number of frames to skip before each roundrobin step (default: 1)
roundrobin_skip 1
# Try to filter out noise generated by roundrobin (default: off)
switchfilter off
############################################################
# Motion Detection Settings:
############################################################
# Threshold for number of changed pixels in an image that
# triggers motion detection (default: 1500)
threshold 1500
# Automatically tune the threshold down if possible (default: off)
threshold_tune off
# Noise threshold for the motion detection (default: 32)
noise_level 32
# Automatically tune the noise threshold (default: on)
noise_tune on
# Despeckle motion image using (e)rode or (d)ilate or (l)abel (Default: not defined)
# Recommended value is EedDl. Any combination (and number of) of E, e, d, and D is valid.
# (l)abeling must only be used once and the 'l' must be the last letter.
# Comment out to disable
despeckle_filter EedDl
# Detect motion in predefined areas (1 - 9). Areas are numbered like that: 1 2 3
# A script (on_area_detected) is started immediately when motion is 4 5 6
# detected in one of the given areas, but only once during an event. 7 8 9
# One or more areas can be specified with this option. (Default: not defined)
; area_detect value
# PGM file to use as a sensitivity mask.
# Full path name to. (Default: not defined)
; mask_file value
# Dynamically create a mask file during operation (default: 0)
# Adjust speed of mask changes from 0 (off) to 10 (fast)
smart_mask_speed 0
# Ignore sudden massive light intensity changes given as a percentage of the picture
# area that changed intensity. Valid range: 0 - 100 , default: 0 = disabled
lightswitch 0
# Picture frames must contain motion at least the specified number of frames
# in a row before they are detected as true motion. At the default of 1, all
# motion is detected. Valid range: 1 to thousands, recommended 1-5
minimum_motion_frames 1
# Specifies the number of pre-captured (buffered) pictures from before motion
# was detected that will be output at motion detection.
# Recommended range: 0 to 5 (default: 0)
# Do not use large values! Large values will cause Motion to skip video frames and
# cause unsmooth movies. To smooth movies use larger values of post_capture instead.
pre_capture 0
# Number of frames to capture after motion is no longer detected (default: 0)
post_capture 0
# Event Gap is the seconds of no motion detection that triggers the end of an event
# An event is defined as a series of motion images taken within a short timeframe.
# Recommended value is 60 seconds (Default). A value of 0 allows to generate 'gapless'
# movies - an event ends right after post_capture if any. The value -1 is allowed and
# disables events causing all Motion to be written to one single movie file and no
# pre_capture.
event_gap 60
# Maximum length in seconds of a movie
# When value is exceeded a new movie file is created. (Default: 0 = infinite)
max_movie_time 0
# Always save images even if there was no motion (default: off)
emulate_motion off
############################################################
# Image File Output
############################################################
# Output 'normal' pictures when motion is detected (default: on)
# Valid values: on, off, first, best, center
# When set to 'first', only the first picture of an event is saved.
# Picture with most motion of an event is saved when set to 'best'.
# Picture with motion nearest center of picture is saved when set to 'center'.
# Can be used as preview shot for the corresponding movie.
output_pictures on
# Output pictures with only the pixels moving object (ghost images) (default: off)
output_debug_pictures off
# The quality (in percent) to be used by the jpeg compression (default: 75)
quality 75
# Type of output images
# Valid values: jpeg, ppm (default: jpeg)
picture_type jpeg
############################################################
# FFMPEG related options
# Film (movies) file output, and deinterlacing of the video input
# The options movie_filename and timelapse_filename are also used
# by the ffmpeg feature
############################################################
# Use ffmpeg to encode movies in realtime (default: off)
ffmpeg_output_movies on
# Use ffmpeg to make movies with only the pixels moving
# object (ghost images) (default: off)
ffmpeg_output_debug_movies off
# Use ffmpeg to encode a timelapse movie
# Default value 0 = off - else save frame every Nth second
ffmpeg_timelapse 0
# The file rollover mode of the timelapse video
# Valid values: hourly, daily (default), weekly-sunday, weekly-monday, monthly, manual
ffmpeg_timelapse_mode daily
# Bitrate to be used by the ffmpeg encoder (default: 400000)
# This option is ignored if ffmpeg_variable_bitrate is not 0 (disabled)
ffmpeg_bps 500000
# Enables and defines variable bitrate for the ffmpeg encoder.
# ffmpeg_bps is ignored if variable bitrate is enabled.
# Valid values: 0 (default) = fixed bitrate defined by ffmpeg_bps,
# or the range 2 - 31 where 2 means best quality and 31 is worst.
ffmpeg_variable_bitrate 0
# Codec to used by ffmpeg for the video compression.
# Timelapse mpegs are always made in mpeg1 format independent from this option.
# Supported formats are: mpeg1 (ffmpeg-0.4.8 only), mpeg4 (default), and msmpeg4.
# mpeg1 - gives you files with extension .mpg
# mpeg4 or msmpeg4 - gives you files with extension .avi
# msmpeg4 is recommended for use with Windows Media Player because
# it requires no installation of codec on the Windows client.
# swf - gives you a flash film with extension .swf
# flv - gives you a flash video with extension .flv
# ffv1 - FF video codec 1 for Lossless Encoding ( experimental )
# mov - QuickTime ( testing )
ffmpeg_video_codec mpeg4
# Use ffmpeg to deinterlace video. Necessary if you use an analog camera
# and see horizontal combing on moving objects in video or pictures.
# (default: off)
ffmpeg_deinterlace off
############################################################
# External pipe to video encoder
# Replacement for FFMPEG builtin encoder for ffmpeg_output_movies only.
# The options movie_filename and timelapse_filename are also used
# by the ffmpeg feature
#############################################################
# Bool to enable or disable extpipe (default: off)
use_extpipe off
# External program (full path and opts) to pipe raw video to
# Generally, use '-' for STDIN...
;extpipe mencoder -demuxer rawvideo -rawvideo w=320:h=240:i420 -ovc x264 -x264encopts bframes=4:frameref=1:subq=1:scenecut=-1:nob_adapt:threads=1:keyint=1000:8x8dct:vbv_bufsize=4000:crf=24:partitions=i8x8,i4x4:vbv_maxrate=800:no-chroma-me -vf denoise3d=16:12:48:4,pp=lb -of avi -o %f.avi - -fps %fps
############################################################
# Snapshots (Traditional Periodic Webcam File Output)
############################################################
# Make automated snapshot every N seconds (default: 0 = disabled)
snapshot_interval 0
############################################################
# Text Display
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second, %T = HH:MM:SS,
# %v = event, %q = frame number, %t = thread (camera) number,
# %D = changed pixels, %N = noise level, \n = new line,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
# %C = value defined by text_event - do not use with text_event!
# You can put quotation marks around the text to allow
# leading spaces
############################################################
# Locate and draw a box around the moving object.
# Valid values: on, off, preview (default: off)
# Set to 'preview' will only draw a box in preview_shot pictures.
locate_motion_mode off
# Set the look and style of the locate box if enabled.
# Valid values: box, redbox, cross, redcross (default: box)
# Set to 'box' will draw the traditional box.
# Set to 'redbox' will draw a red box.
# Set to 'cross' will draw a little cross to mark center.
# Set to 'redcross' will draw a little red cross to mark center.
locate_motion_style box
# Draws the timestamp using same options as C function strftime(3)
# Default: %Y-%m-%d\n%T = date in ISO format and time in 24 hour clock
# Text is placed in lower right corner
text_right %Y-%m-%d\n%T-%q
# Draw a user defined text on the images using same options as C function strftime(3)
# Default: Not defined = no text
# Text is placed in lower left corner
; text_left CAMERA %t
# Draw the number of changed pixed on the images (default: off)
# Will normally be set to off except when you setup and adjust the motion settings
# Text is placed in upper right corner
text_changes off
# This option defines the value of the special event conversion specifier %C
# You can use any conversion specifier in this option except %C. Date and time
# values are from the timestamp of the first image in the current event.
# Default: m%dM%S
# The idea is that %C can be used filenames and text_left/right for creating
# a unique identifier for each event.
text_event m%dM%S
# Draw characters at twice normal size on images. (default: off)
text_double off
############################################################
# Target Directories and filenames For Images And Films
# For the options snapshot_, picture_, movie_ and timelapse_filename
# you can use conversion specifiers
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second,
# %v = event, %q = frame number, %t = thread (camera) number,
# %D = changed pixels, %N = noise level,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
# %C = value defined by text_event
# Quotation marks round string are allowed.
############################################################
# Target base directory for pictures and films
# Recommended to use absolute path. (Default: current working directory)
target_dir /hoe/111/motionrec
# File path for snapshots (jpeg or ppm) relative to target_dir
# Default: %v-m%dM%S-snapshot
# Default value is equivalent to legacy oldlayout option
# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-snapshot
# File extension .jpg or .ppm is automatically added so do not include this.
# Note: A symbolic link called lastsnap.jpg created in the target_dir will always
# point to the latest snapshot, unless snapshot_filename is exactly 'lastsnap'
snapshot_filename %v-m%dM%S-snapshot
# File path for motion triggered images (jpeg or ppm) relative to target_dir
# Default: %v-m%dM%S-%q
# Default value is equivalent to legacy oldlayout option
# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-%q
# File extension .jpg or .ppm is automatically added so do not include this
# Set to 'preview' together with best-preview feature enables special naming
# convention for preview shots. See motion guide for details
picture_filename %v-m%dM%S-%q
# File path for motion triggered ffmpeg films (movies) relative to target_dir
# Default: %v-m%dM%S
# Default value is equivalent to legacy oldlayout option
# For Motion 3.0 compatible mode choose: %Y/%m/%d/M%S
# File extension .mpg or .avi is automatically added so do not include this
# This option was previously called ffmpeg_filename
movie_filename %v-m%dM%S
# File path for timelapse movies relative to target_dir
# Default: m%d-timelapse
# Default value is near equivalent to legacy oldlayout option
# For Motion 3.0 compatible mode choose: %Y/%m/%d-timelapse
# File extension .mpg is automatically added so do not include this
timelapse_filename m%d-timelapse
############################################################
# Global Network Options
############################################################
# Enable or disable IPV6 for http control and stream (default: off )
ipv6_enabled off
############################################################
# Live Stream Server
############################################################
# The mini-http server listens to this port for requests (default: 0 = disabled)
stream_port 8081
# Quality of the jpeg (in percent) images produced (default: 50)
stream_quality 50
# Output frames at 1 fps when no motion is detected and increase to the
# rate given by stream_maxrate when motion is detected (default: off)
stream_motion off
# Maximum framerate for stream streams (default: 1)
stream_maxrate 1
# Restrict stream connections to localhost only (default: on)
stream_localhost off
# Limits the number of images per connection (default: 0 = unlimited)
# Number can be defined by multiplying actual stream rate by desired number of seconds
# Actual stream rate is the smallest of the numbers framerate and stream_maxrate
stream_limit 0
# Set the authentication method (default: 0)
# 0 = disabled
# 1 = Basic authentication
# 2 = MD5 digest (the safer authentication)
stream_auth_method 0
# Authentication for the stream. Syntax username:password
# Default: not defined (Disabled)
; stream_authentication username:password
############################################################
# HTTP Based Control
############################################################
# TCP/IP port for the http server to listen on (default: 0 = disabled)
webcontrol_port 8080
# Restrict control connections to localhost only (default: on)
webcontrol_localhost on
# Output for http server, select off to choose raw text plain (default: on)
webcontrol_html_output on
# Authentication for the http based control. Syntax username:password
# Default: not defined (Disabled)
; webcontrol_authentication username:password
############################################################
# Tracking (Pan/Tilt)
#############################################################
# Type of tracker (0=none (default), 1=stepper, 2=iomojo, 3=pwc, 4=generic, 5=uvcvideo, 6=servo)
# The generic type enables the definition of motion center and motion size to
# be used with the conversion specifiers for options like on_motion_detected
track_type 0
# Enable auto tracking (default: off)
track_auto off
# Serial port of motor (default: none)
;track_port /dev/ttyS0
# Motor number for x-axis (default: 0)
;track_motorx 0
# Set motorx reverse (default: 0)
;track_motorx_reverse 0
# Motor number for y-axis (default: 0)
;track_motory 1
# Set motory reverse (default: 0)
;track_motory_reverse 0
# Maximum value on x-axis (default: 0)
;track_maxx 200
# Minimum value on x-axis (default: 0)
;track_minx 50
# Maximum value on y-axis (default: 0)
;track_maxy 200
# Minimum value on y-axis (default: 0)
;track_miny 50
# Center value on x-axis (default: 0)
;track_homex 128
# Center value on y-axis (default: 0)
;track_homey 128
# ID of an iomojo camera if used (default: 0)
track_iomojo_id 0
# Angle in degrees the camera moves per step on the X-axis
# with auto-track (default: 10)
# Currently only used with pwc type cameras
track_step_angle_x 10
# Angle in degrees the camera moves per step on the Y-axis
# with auto-track (default: 10)
# Currently only used with pwc type cameras
track_step_angle_y 10
# Delay to wait for after tracking movement as number
# of picture frames (default: 10)
track_move_wait 10
# Speed to set the motor to (stepper motor option) (default: 255)
track_speed 255
# Number of steps to make (stepper motor option) (default: 40)
track_stepsize 40
############################################################
# External Commands, Warnings and Logging:
# You can use conversion specifiers for the on_xxxx commands
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second,
# %v = event, %q = frame number, %t = thread (camera) number,
# %D = changed pixels, %N = noise level,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
# %C = value defined by text_event
# %f = filename with full path
# %n = number indicating filetype
# Both %f and %n are only defined for on_picture_save,
# on_movie_start and on_movie_end
# Quotation marks round string are allowed.
############################################################
# Do not sound beeps when detecting motion (default: on)
# Note: Motion never beeps when running in daemon mode.
quiet on
# Command to be executed when an event starts. (default: none)
# An event starts at first motion detected after a period of no motion defined by event_gap
; on_event_start value
# Command to be executed when an event ends after a period of no motion
# (default: none). The period of no motion is defined by option event_gap.
; on_event_end value
# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
# To give the filename as an argument to a command append it with %f
; on_picture_save value
# Command to be executed when a motion frame is detected (default: none)
; on_motion_detected value
# Command to be executed when motion in a predefined area is detected
# Check option 'area_detect'. (default: none)
; on_area_detected value
# Command to be executed when a movie file (.mpg|.avi) is created. (default: none)
# To give the filename as an argument to a command append it with %f
; on_movie_start value
# Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
# To give the filename as an argument to a command append it with %f
; on_movie_end value
# Command to be executed when a camera can't be opened or if it is lost
# NOTE: There is situations when motion don't detect a lost camera!
# It depends on the driver, some drivers dosn't detect a lost camera at all
# Some hangs the motion thread. Some even hangs the PC! (default: none)
; on_camera_lost value
#####################################################################
# Common Options for database features.
# Options require database options to be active also.
#####################################################################
# Log to the database when creating motion triggered picture file (default: on)
; sql_log_picture on
# Log to the database when creating a snapshot image file (default: on)
; sql_log_snapshot on
# Log to the database when creating motion triggered movie file (default: off)
; sql_log_movie off
# Log to the database when creating timelapse movies file (default: off)
; sql_log_timelapse off
# SQL query string that is sent to the database
# Use same conversion specifiers has for text features
# Additional special conversion specifiers are
# %n = the number representing the file_type
# %f = filename with full path
# Default value:
# insert into security(camera, filename, frame, file_type, time_stamp, text_event) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
; sql_query insert into security(camera, filename, frame, file_type, time_stamp, event_time_stamp) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
############################################################
# Database Options
############################################################
# database type : mysql, postgresql, sqlite3 (default : not defined)
; database_type value
# database to log to (default: not defined)
; database_dbname value
# The host on which the database is located (default: localhost)
; database_host value
# User account name for database (default: not defined)
; database_user value
# User password for database (default: not defined)
; database_password value
# Port on which the database is located
# mysql 3306 , postgresql 5432 (default: not defined)
; database_port value
############################################################
# Database Options For SQLite3
############################################################
# SQLite3 database (file path) (default: not defined)
; sqlite3_db value
############################################################
# Video Loopback Device (vloopback project)
############################################################
# Output images to a video4linux loopback device
# The value '-' means next available (default: not defined)
; video_pipe value
# Output motion images to a video4linux loopback device
# The value '-' means next available (default: not defined)
; motion_video_pipe value
##############################################################
# Thread config files - One for each camera.
# Except if only one camera - You only need this config file.
# If you have more than one camera you MUST define one thread
# config file for each camera in addition to this config file.
##############################################################
# Remember: If you have more than one camera you must have one
# thread file for each camera. E.g. 2 cameras requires 3 files:
# This motion.conf file AND thread1.conf and thread2.conf.
# Only put the options that are unique to each camera in the
# thread config files.
; thread /usr/local/etc/thread1.conf
; thread /usr/local/etc/thread2.conf
; thread /usr/local/etc/thread3.conf
; thread /usr/local/etc/thread4.conf
Environment
Motion version: |
3.2.11.1 (3.2.11.1-3.fc12) |
ffmpeg version: |
0.5-5.20091026svn.fc12 |
Libraries: |
ffmpeg, mysql |
Server OS: |
Fedora 12 , 2.6.32.11-99.fc12.x86_64 |
--
PavelM345 - 27 Apr 2010
Answer
Some description of reasons of this problem, and direction for solution could be found here:
http://www.zoneminder.com/forums/viewtopic.php?p=62947
if i am lucky, i find the solution for Motion. But at first i'll try Zoneminder.
BRGDS
PavelM345